Browse all practice questions for the Task Group 142 Tolerances Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Task Group 142 Tolerances Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • How would you interpret a callout with 'Ø0.050' and a position tolerance '0.010 A B'?
  • What is the purpose of a datum in GD&T?
  • Which tolerances govern how far a feature's centerline or surface is from a datum reference?
  • How is the height of a projected tolerance zone specified?
  • Which QA mechanical test is ALWAYS 2 mm regardless of technique?
  • Which option correctly states the annual requirement for following manufacturer's test procedures?
  • In respiratory gating, the annual beam output constancy tolerance is expressed as what percentage?
  • What is the annual TBI/TSET output calibration tolerance?
  • What is required for beam-on indicator?
  • What is the monthly light/radiation field coincidence tolerance on a side?
  • What is the monthly cross-hair centering (walkout) tolerance?
  • What is the annual electron applicator interlocks tolerance?
  • How often is the electron output constancy tolerance measured for most machines?
  • What is the annual couch rotation isocenter tolerance?
  • What is the CT number accuracy tolerance for water?
  • How is a hole pattern evaluated against datums A and B?
  • What is the monthly gantry/collimator angle indicator tolerance?
  • What is the monthly gating interlock tolerance?
  • What is compound position tolerance?
  • Which statement best defines a datum in GD&T?
  • Which two electron beam parameters have a 1% annual tolerance from baseline?
  • When evaluating a hole pattern with datums A and B, what is required for each hole axis?
  • To verify multiple holes in a pattern, what provides the orientation and location reference?
  • What is the annual wedge transmission factor constancy tolerance?
  • What is the purpose of MMC in relation to position tolerances?
  • What is the annual TBI/TSET mode tolerance?
  • What is the annual SRS arc rotation mode tolerance (range 0.5-10 MU/deg)?
  • Which tolerance is commonly described as walkout?
  • Which monthly QA tolerance is specified for the backup monitor chamber constancy?
  • Which statement about a basic dimension is accurate?
  • What is the effect of a projected tolerance zone on mating part clearance at projection height?
  • Which statement correctly distinguishes flatness from straightness?
  • What is the annual PDD or TMR and OAF constancy tolerance?
  • Which tolerance is identical across all modalities at isocenter?
  • What is the daily X-ray output constancy tolerance?
  • Which monthly X-ray output constancy tolerance is specified?
  • Which statement best describes a datum feature?
  • What is the monthly phase/amplitude beam control tolerance?
  • Which tolerance category controls the actual shape of a feature boundary?
  • Which description best characterizes the annual TBI/TSET mode tolerance?
  • What is the requirement for stereotactic interlocks in SRS/SBRT?
  • Which tolerance describes the arc mode allowance in MU per degree?
  • What is the monthly typical dose rate output constancy tolerance?
  • What is the monthly distance tolerance between lasers and the front pointer?
  • What is the monthly accessory tray position tolerance?
  • What is the monthly symmetric jaw position indicator tolerance?
  • What is the daily ODI tolerance at isocenter for Non-IMRT, IMRT, and SRS-SBRT?
  • What is the annual X-ray beam quality tolerance measured as PDD or TMR from baseline?
  • Which tolerance is used to specify CT number accuracy for water in imaging QA?
  • What is 'runout' used to control on a mounting surface?
  • For holes, where does MMC occur?
  • Which statement differentiates circular runout from total runout?
  • What is the role of a datum feature symbol in GD&T?
  • What is the annual enhanced dynamic or gated delivery dose tolerance expressed as?
  • What is the annual beam output constancy tolerance for respiratory gating?
  • Which statement best reflects the laser localization tolerances for Non-IMRT, IMRT, and SRS-SBRT?
  • Which tolerance has a value of 2 mm for the accessory tray position?
  • What is the annual TBI/TSET accessories tolerance?
  • What is the X-ray monitor unit linearity tolerance for MU values ≤5?
  • What scenario necessitates using a datum target?
  • Which tolerance is described with angular units rather than linear millimeters?
  • What is the monthly X-ray output constancy tolerance?
  • What is a projected tolerance zone used for?
  • What is the monthly photon beam profile constancy tolerance?
  • What is a bilateral tolerance?
  • What is the difference between 'diameter' and 'distance' in tolerancing?
  • Which statement correctly describes the annual enhanced dynamic or gated delivery dose tolerance?
  • Which tolerance is specified for CT number accuracy in water regions?
  • What is the requirement for the door interlock (beam off)?
  • Which of the following describes the CT number accuracy tolerance for water-equivalent materials?
  • How are datums chosen and ordered in a frame?
  • What is the annual table travel maximum range tolerance (all directions)?
  • What is a datum axis?
  • How does a GD&T callout indicate that a feature must be located within a cylindrical zone rather than a square zone?
  • What is the annual spot check of field size dependent output factors tolerance?
  • Which statement about a datum is correct in GD&T terms?
  • The annual enhanced dynamic or gated delivery dose tolerance is described as which of the following?
  • What is the monthly tolerance for latching of wedges and blocking tray?
  • What is the annual electron symmetry change tolerance from baseline?
  • What is the monthly asymmetric light/radiation field coincidence tolerance on a side?
  • What is the annual stereotactic accessories/lockouts tolerance?
  • How do you interpret a callout that uses a profile tolerance and a separate positional tolerance?
  • What is the annual requirement for following manufacturer's test procedures?
  • What is the monthly laser guard interlock test tolerance?
  • What is the monthly in-room respiratory monitoring system tolerance?
  • Which statement best describes a three-datum frame in GD&T?
  • What is the key safety QA requirement across ALL modalities?
  • Which tolerance is expressed in millimeters for the annual QA tolerances?
  • What is the annual coincidence of radiation and mechanical isocenter tolerance?
  • When is a datum target necessary?
  • What is the requirement for a radiation area monitor?
  • What does the term 'datum axis' refer to in GD&T?
  • Which statement correctly describes unilateral tolerances?
  • What is the requirement for the door closing safety system?
  • What does profile of a surface refer to in GD&T?
  • What is the electron output constancy requirement?
  • What is the annual enhanced dynamic or gated delivery dose tolerance?
  • How does a profile of a surface tolerance relate to form and orientation?
  • For SRS/SBRT procedures, what is the annual coincidence tolerance between radiation and mechanical isocenters?
  • Which tolerance is the monthly beam output constancy tolerance for respiratory gating?
  • Which tolerance is defined as 2 mm or 1% on a side?
  • How is LMC defined for a shaft feature?
  • What is the effect of the M modifier in a GD&T callout?
  • Which tolerance describes the monthly phase/amplitude beam control?
  • Which monthly tolerance category applies to interlock-related tests such as gating interlock?
  • Why is a basic dimension critical in a true-position callout?
  • For respiratory gating, what is the annual beam output constancy tolerance?
  • Which tolerance is defined as 1% for TBI and 1 mm PDD shift for TSET?
  • Which monthly QA tolerance applies to the photon beam profile constancy?
  • What is the annual electron output constancy vs gantry angle tolerance?
  • True position tolerance is evaluated relative to which frame?
  • How is LMC defined for a hole feature?
  • What is the purpose of a datum target?
  • What is the annual table angle tolerance?
  • What is required for audiovisual monitors?
  • What is the role of a datum axis in a cylindrical part?
  • What is the significance of the "remainder of the surface is free of tolerances"?
  • What is the annual X-ray beam quality (PDD or TMR) tolerance?
  • Which monthly tolerance is specified for the gating interlock?
  • What is the monthly electron beam energy constancy tolerance?
  • What is the annual arc mode (expected MU/deg) tolerance?
  • Which of the following describes the relationship between datums and measurement methods?
  • How is a datum reference frame used to evaluate a pattern of holes?
  • What is the result of applying a position tolerance to a hole with an MMC modifier?
  • What is the annual X-ray output constancy vs dose rate tolerance?
  • In respiratory gating, the annual dose delivery accuracy tolerance is best described as within MU of the expected delivery?
  • When a hole has an MMC modifier, the actual tolerance is determined by:
  • How does GD&T separate form, orientation, and location tolerances?
  • How do you interpret a dimension labeled Ø0.010 in GD&T?
  • Which tolerance governs the symmetric jaw position indicator?
  • What is the annual tolerance for electron and X-ray output constancy with respect to gantry angle?
  • What does true position refer to in GD&T?
  • What is the annual output factors for electron applicators tolerance?
  • Among Non-IMRT, IMRT, and SRS-SBRT, which modality has the smallest daily laser localization tolerance?
  • Which statement is true about safety system functionality?
  • What is a unilateral tolerance?
  • What is the annual X-ray monitor unit linearity tolerance?
  • Which statement about a basic dimension is accurate?
  • What is the monthly electron output constancy tolerance?
  • What does the diameter symbol indicate in a GD&T frame?
  • The CT number accuracy tolerance for water is which value?
  • Which tolerance is expressed as a linear millimeter value for table movement?
  • What is the monthly phase/amplitude beam control tolerance?
  • How does "concentricity" differ from "position" tolerance?
  • Daily collimator size indicator tolerance for Non-IMRT, IMRT, and SRS-SBRT?
  • What is the annual gantry rotation isocenter tolerance?
  • What is the difference between 'profile of a line' and 'profile of a surface' in terms of control?
  • What is the annual electron monitor unit linearity tolerance?
  • Which tolerance requires a cylindrical tolerance zone coaxial with a datum axis?
  • How would you evaluate a hole's true position with datums A, B, and C?
  • Profile of a line controls which of the following?
  • Which statement best defines perpendicularity and angularity?
  • How is concentricity evaluated?
  • What is the annual table top sag tolerance?
  • How does a projected tolerance zone affect assembly clearance?
  • What is the monthly localizing laser tolerance?
  • In GD&T, regarding holes and shafts, which statement correctly describes MMC/LMC?
  • Which tolerances govern the angular relationship, tilt, or alignment of features to datums?
  • Which statement is NOT part of a standard feature control frame?
  • What is the monthly asymmetric jaw position indicator tolerance?
  • How would you verify a part that uses a three-datum frame in production?
  • What is the monthly beam output constancy tolerance for respiratory gating?
  • Which modality has the strictest daily laser localization tolerance?
  • What is the monthly electron beam profile constancy tolerance?
  • What is the annual X-ray output constancy vs gantry angle tolerance?
  • What is a datum target?
  • Which statement best describes profile of a surface?
  • What is the annual electron beam quality tolerance?
  • Which tolerance applies to annual TBI/TSET output calibration?
  • What is the annual electron and X-ray output constancy vs gantry angle tolerance?
  • What is the annual X-ray flatness change from baseline tolerance?
  • What is the difference between 'true position' and 'actual position'?
  • Which tolerance includes both a linear and an angular component?
  • For respiratory gating, the annual dose delivery accuracy tolerance is within how many MU of the expected delivery?
  • Which monthly QA tolerance is listed for the electron beam output?
  • Which element is NOT part of a standard feature control frame?
  • When would you use a true position callout on a hole feature?
  • What is the annual electron flatness change tolerance from baseline?
  • What is the monthly compensator placement accuracy tolerance?
  • Which tolerance relates to the table sag, stated as 2 mm?
  • In respiratory gating, the annual dose delivery accuracy tolerance is described as within how many MU of the expected delivery?
  • What is the annual X-ray/electron output calibration tolerance (TG-51)?
  • What is the monthly treatment couch position indicator tolerance?
  • What is the monthly wedge placement accuracy tolerance?
  • Which tolerance describes the annual X-ray symmetry change from baseline?
  • What is the annual collimator rotation isocenter tolerance?
  • What are the three components of a standard feature control frame?
  • For SRS arc rotation mode, what is the tolerance for gantry angle vs delivered?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy